 |
 |
 |
| |
Important Specifications
- Thickness of door: 32 mm, 35mm &40mm/ Thickness of Door skin: 4mm.
- Size of Door: 774 mm x 2150 mm, 850 mm x 2150 mm and 926 mm x 2150 mm
- Size of door skin: 900 mm X 2100 mm
- Types of door and door skins: 2 panel, 4 panel and 6 panel
|
| |
REQUIREMENT FOR RAISED PANEL FIBERBOARD SKINS AS PER IS: 15380:2003 |
| Sr. No |
Requirements |
Permissible Limits |
Methods of Tests, Ref to IS |
| 1 |
2 |
3 |
4 |
 |
| 1 |
Density, kg/m³ |
> 1000 |
2380 (Part 3) |
| 2 |
Moisture content, percent, Max |
8 |
2380 (Part 3) |
| 3 |
Water absorption, percent:
After 2 hrs
After 24 hrs |
<16
<36 |
2380 (Part16) |
| 4 |
Swelling in water, percent, Max
a) General absorption, 24 hrs |
EN 13329 |
> 9500 rev
(AC 5; > 6500 rev) |
|
i) Thickness |
20 |
2380 (Part17) |
|
ii) Length |
0.70 |
|
|
iii) Width |
0.70 |
|
|
b) Surface absorption |
9 |
|
| 5 |
Modulus of rupture, N/mm² Min |
35 |
2380 (Part 4) |
| 6 |
Internal bond strength, N/mm² Min: |
|
|
| |
a) Dry state |
1.0 |
|
| |
b) Wet state (2 hrs boiling) |
0.3 |
|
| 7 |
Immersion in boiling water at 100 ± 3 º C for 4 hrs |
No Disintegration |
|
| 8 |
Formaldehyde emission |
< 9 mg / 100 g |
13745 |
|
|
| |
MOULDED RAISED HIGH DENSITY FIBRE (HDF) PANEL DOORS- TEST PARAMETERS AND VALUES AS PER :IS: 4020:1994 |
| Sr. No |
Test |
Requirements of IS :4020 |
|
| 1 |
Dimensions and Square ness |
Length width: ± 5 mm Thickness: ± 1 mmSquare ness: 1 mm at a length of 500 mm |
| 2 |
General Flatness |
< 6.0 mm |
| 3 |
Local Plainness |
<0.5 mm |
| 4 |
Impact Indentation |
<0.2 mm |
| 5 |
Flexure Test |
Residual deflection < 1/ 10th of max. Deflection.Max.Deflection < 1/30th of length & < 1/15th of width whichever is less. |
| 6 |
Edge Loading Test |
Max Deflection < 5.0mm
Residual deflection <0.5mm
Lateral buckling <2.0mm |
| 7 |
Shock Resistance Test |
Should withstand 5 impacts |
| 8 |
Buckling Test |
Initial deflection <50 mm
Res. deflection <5.0 mm |
| 9 |
Slamming Test |
100 impact without any damage |
| 10 |
Misuse Test |
Pass |
| 11 |
Varying Humidity Test |
Max departure from plainness <1 mm
Recovery to original size > 90 % |
| 12 |
End Immersion Test |
No delamination in one cycle |
| 13 |
Knife Test |
Pass |
| 14 |
Glue Adhesion Test |
Pass |
| 15 |
Screw withdrawal Resistance |
> 1000 N |
|
|
|
|
|
